[ULTRAMONKEY-USERS] ultramonkey load balancing virtual ip

[diego]

mmmh... what logfile="/var/log/ldirectord.log"says?
or ha.log...


I'm not sure... but look this sequence of commands for Debian:

usr/sbin/update-rc.d heartbeat start 75 2 3 4 5 . stop 05 0 1 6 .
/usr/sbin/update-rc.d -f heartbeat remove
/etc/init.d/heartbeat stop
/etc/init.d/ldirectord start

In this case (http://www.ultramonkey.org/3/topologies/lb-eg.html), may be the opposite of 
what I told you before: I was referring to my config, where heartbeat start ldirector, but
here ldirector starts and then heartbeat come started...


Are you using CentOS ?


Diego


Abraham olivares Varela ha scritto:
> Hi Diego,
> 
> As i told you i used the configration, ldirectord is running but i don't 
> know why it didn't create the Virtual IP.
> 
> Please take a look
> 
>  # /sbin/ip addr sh
> 
> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>     inet 127.0.0.1/8 scope host lo
>     inet6 ::1/128 scope host
>         valid_lft forever preferred_lft forever
> 
> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast 
> qlen 1000
>     link/ether 00:19:db:75:d2:27 brd ff:ff:ff:ff:ff:ff
>     inet 192.168.1.66/24 brd 192.168.1.255 scope global eth0
>     *****normally here there will be the virtaul IP************
>     inet6 fe80::219:dbff:fe75:d227/64 scope link
>         valid_lft forever preferred_lft forever
> 
> 3: sit0: <NOARP> mtu 1480 qdisc noop
>     link/sit 0.0.0.0 brd 0.0.0.0
> 
> Thanks and Best Regards
>  Abraham OLIVARES
> 
> */diego <diego131334 at yahoo.it>/* escribió:
> 
>     as you wrote, the procedure at the link below explicitly stop
>     Heartbeat and start
>     ldirector, so it is normal to have ha stopped!
> 
>     for load balancing alone, heartbeat is stopped, of course.
> 
>     In your case Ldirector starts at the boot (/etc/init.d/ldirector
>     start) is not started by
>     heartbeat.
> 
>     To test: the call to the virtual node, must work :)
> 
>     If you meant to test HOW the algorithm work , i don't know...
> 
>     Diego
> 
>     Abraham olivares Varela ha scritto:
>      >
>      > Thanks for yous answer
>      >
>      > another question i understood than heartbeat starts ldirecord but
>     when
>      > i checked the status of heartbeat.
>      >
>      > # /etc/init.d/heartbeat status
>      > heartbeat is stopped. No process
>      >
>      > I configured heartbeat for High Availability but for load
>     balancing i
>      > used the following link to do it and it didn't say nothing about
>      > heartbeat's conf.
>      >
>      > http://www.ultramonkey.org/3/topologies/lb-eg.html
>      >
>      > how can i test if my load balancind conf is working properly?
>      >
>      > Thanks and Best Regards
>      > Abraham OLIVARES
>      >
>      >
>      >
> 
> 
> ------------------------------------------------------------------------
> 
> ¡Sé un mejor fotógrafo!
> Perfecciona tu técnica y encuentra las mejores fotos en:
> http://mx.yahoo.com/promos/mejorambientalista.html